[ad_1]
Query 1:
From Joe:
Each different week I very a lot look ahead to this podcast. I particularly benefit from the whimsical music outtros Ben does sometimes.
Within the very close to future, I’m going to start out making Christian Becksvoort’s icon 15-drawer chest as proven in his guide Shaker Inspiration: 5 A long time of Tremendous Craftsmanship. I’ve seen on this piece, in addition to most of the others in FWW that the underside “rail” has a swish arch. Becksvoort makes it out of three items of wooden with 45-degree miters. I’d be ever so grateful in the event you may please discover out why he makes use of three items reasonably than only one piece of wooden.
Many thanks for all the assistance through the years and I look ahead to when Anisa has one other video with Becksvoort consuming strawberries and chatting. That was considered one of my favourite FWW movies.
Query 2:
From Tom:
I’m remodeling a bench that belonged to my mom’s cousin who was additionally a woodworker. This was his main bench and a whole lot of furnishings was constructed on it.
Once I flipped the bench high over, there have been three deep mortises lower throughout the bench. These mortises are 1 1/2 ” deep and three/4″ huge within the 2 1/4″ thick high. The highest was clearly supposed for another goal. I’ve some 2 x 3/4″ exhausting maple items that I intend to chop into 3/4″ blocks to attach into these mortises. I plan to attach them in such a means as to keep up the grain path. Because the inventory I’ve is simply 3/4″ I’ll should stack them 2 deep to fill the mortise and I plan to stagger the glue joints.
The questions:
Clearly, I’ve acquired a whole lot of finish grain to finish grain. The glue joint within the backside of the mortise and between the blocks will likely be facet grain and will likely be very sturdy. However the joint between the blocks and the perimeters of the mortise will all be finish grain.
Ought to I simply use Titebond and settle for the top grain joint? Change glues to an epoxy which can work higher with finish grain. One thing else?
Why am I doing this?
I’ve some exhausting maple readily available that’s sized virtually completely for the job.
I’ve the bench aside and the highest flipped the other way up. If I’m going to do something about it now could be the time.
It appears to me that solely having 3/4″ of wooden above these mortises constitutes a weak spot. Though the complete high rests on the bench body (the highest stretchers are set so the highest rests on all of them the way in which across the perimeter from leg to leg) it isn’t prone to flex and crack. But when it does flex, it’ll be alongside that line of end-grain joints.
Query 3:
From James:
Thanks for what you do! I’ve been uncovered to a ton of data and useful data by listening to y’all.
I began sketching out a wall shelf software holder to carry my most used instruments after I stumbled onto a pic of 1 that seemed similar to what I envisioned at The Austin Faculty of Furnishings and Design.
There’s acquired to be a easy reply…
What’s the easiest way to make 2 cabinets facet by facet on the similar peak? (Pic connected – too & backside shelf) Forgive me if my phrases are unsuitable. Nonetheless studying. One middle tenon on one shelf, and a double tenon on the opposite so there’s mainly 3 mortises evenly spaced by means of the middle upright? Dowels in either side – most likely not as sturdy, however simpler? I’ve all the time averted cabinets and most furnishings does as effectively. I’m positive it’s that easy however as a beginner thought perhaps I’m oversimplifying, or there was a trick I do t know of. Despite the fact that for me that will likely be stretching my expertise.
Listener suggestion:
From Declan:
I stumbled throughout a present on HBOMax not too long ago known as “The Craftsman”. The present is a couple of grasp craftsman by the identify of Eric Holonbeck (SP) a man in his 70s from Eureka California who does some AMAZING work with tools that’s older than himself. (Peddle-powered scroll saws, a single move shaper that makes molded picket gutters out of 4×4, and many different loopy stuff). It’s sort of scary to observe them in use …. security just isn’t a giant deal …. no security glasses, no respirators, no noticed push instruments, and fingers are scarily near the enterprise finish of the machine, it’s like working a suspense thriller about woodworking …. effectively well worth the watch.
Each two weeks, a workforce of Tremendous Woodworking staffers solutions questions from readers on Store Speak Stay, Tremendous Woodworking‘s biweekly podcast. Ship your woodworking inquiries to [email protected] for consideration within the common broadcast! Our continued existence depends upon listener assist. So in the event you benefit from the present, you should definitely go away us a five-star ranking and perhaps even a pleasant touch upon our iTunes web page.
Join eletters as we speak and get the most recent strategies and how-to from Tremendous Woodworking, plus particular presents.
[ad_2]
Supply hyperlink